GF2015 Wireless primary current recorder meter

Primary current recorder.

GF2015 is a wireless primary current recorder equipped with a 433M for transmit the recorded data into the user's PC by our PC-Link software. It is a good assistant of power monitor system. The recording interval can be set from 1- 60 min. The PC-Link software can generate reports and create graphs for profile analysis.

 

Features

  • The primary current recorder uses the same sensor technology as the original rogowski coil. The true RMS inductive sensor does not use magnetic materials. The opening of the sensor is electronically closed and external currents are electronically rejected.
  • The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors. The key feature of the unit is the ability to leave it deployed on the line to record readings every 15 minutes for 90+ days. It easily attaches to the line with a standard insulating bar. Once on the line, it immediate begins to collect and record the primary current on the line.
  • The primary current recorder is equipped with a 433M wireless port for communicating the recorded data into the user’s PC. The data is downloaded through GF2015S PC-Link software, which allows the user to download, view and query the data stored on the primary current recorder.
  • The housing of the primary current recorder is made of ABS+PC and is built to operate safely, even in severe utility environments. It is resistant to shock, repels water and is unsusceptible to flame. It also operates within a wide temperature range. The primary current recorder has the screw insulation bar of installation, which allows it to hang on the line securely in all weather conditions.
  • PC-Link software is a user-friendly software interface that allows the user to download, view, graph and export data from the Primary current recorder into microsoft excel. The data directly transfers from the primary current recorder into excel through a 433M port.
 

Amp Recorder

  • Collect and analyze load profiles
  • Easily clamps to the line in seconds
  • Check for load balance
  • Patented open CT sensor with ±1% accuracy
  • 433M communication with no annoying cables to connect
  • Recorded data quickly downloads into the user's PC
  • PC-Link software interface downloads directly into microsoft excel
  • Generate reports and create graphs for profile analysis

Parameters

Basic parameters
Recording ammeter kit 3 wireless current sensors (GF2015A, GF2015B, GF2015C)
433 HHT (handheld terminal) or 433M wireless data reader (GF2015R)
PC-LinkSoftware software (GF2015S)
Carrying case
Data recording interval 5min, 10min, 15min, 30min;
Interval user settable from 1-60min
Communication distance (wireless) 100m
Communication 433M, 868M or 915M (option)
Installation Installation with electricity; Disassemble with electricity
Battery 3.6 volt lithium battery, 19000mAh; Battery can be replaced
Software requirements PC-Linksoftware & microsoft excel
Processor 100MHz or higher (200MHz or higher recommended)
RAM 32MB, 64M recommended
Drive space 15MB to load software, 10MB of operating Space
Use of position Outdoor or indoor
Electrical parameters 
Range of operation
Voltage 69kV, 35kV, 20KV, 10kV, 6kV
Current 1 to 100A, 1 to 300A, 1 to 600A, 1 to 1000A, 1 to 2000A
Sensor opening Up to 2.5cm
Resolution
1 to 99.9A 0.1A
100 to 2000A 1A
Amps accuracy  ±1% of reading plus 2 counts
Frequency 60Hz (57-63Hz) or 50Hz (47-53Hz) models available
Mechanical parameters 
Dimensions (W×D×H)(cm) 18x9.5x4.62
Weight (kg) 0.58
Environmental conditions
Operating temp. -40°C to 60°C

Download Catalogue

Related Products